Dimensions: 14"x7"x12"

Logo Area: 5"x8"

Capacity: 12 cans plus about 5 pounds of ice

Features:

• Removable Shoulder Strap
• Clip-Down ends
• Twice the insulation of other soft-sided coolers
• Garunteed to hold ice for 24 hours in 120 degree weather
• Leak-Proof Liner
• A side pocket for dry items

Use For:

• Great for daytrips on your Rhino or quad
• Picnics
• Case for Binoculars
• Camera-Bag
• Lunches
• Daytrips
• Bringing an item for dinner or a potlock? Use this cooler to keep things warm as well

Dimensions: 21"x10"x12"

Logo Area: 7"x8"

Capacity: 36 cans plus about 10 pounds of ice

Features:

• Removable Shoulder Strap
• Clip-Down ends
• Twice the insulation of other soft-sided coolers
• Garunteed to hold ice for 24 hours in 120 degree weather
• Leak-Proof Liner
• A side pocket for dry items

Use For:

• Fits in many Rhino racks 
• Hunting and fishing
• Parties
• Sporting Events 

***Meets airplane carry-on requirements

Durable Hi-Impact ABS housing. Anodized aluminum trim ring. Internal starter and ballast. Tempered glass lens. Clear polycarbonate protective lens cover. Easy to wire installation/wireharness and diagram included. 35 watt Euro-Beam light pattern. Light distance 1 mile (5280 ft.). Light Specification - 6,000K Color temperature - 3,200 Lumens - 3.15-3.30 AMP Draw - 2,500+ Hours Bulb Life

FREE SHIPPING!!

Durable Hi-Impact ABS housing. Anodized aluminum trim ring. Internal starter and ballast. Tempered glass lens. Clear polycarbonate protective lens cover. Easy to wire installation/wireharness and diagram included. 35 watt Euro-Beam light pattern. Light Specification - 6,000K Color temperature - 3,200 Lumens - 3.15-3.30 AMP Draw - 2,500+ Hours Bulb Life

FREE SHIPPING!!

Our 9-pack fits perfectly in the standard 6-pack quad rack

Dimensions: 11"x7.5"x8.5"

Logo Area: 4"x7"

Capacity: 9 cans plus about two-and-a-half pounds of ice

Features:

• Removable Shoulder Strap 
• Twice the insulation of other soft-sided coolers
• Garunteed to hold ice for 24 hours in 120 degree weather
• Leak-Proof Liner 

Use For:

• Fits perfectly in the 6-pack quad rack
• Picnics
• Case for Binoculars
• Camera-Bag
• Lunches
• Daytrips

The Yamaha Rhino is a great little side by side, and a super fun vehicle for family off-road sports. However, the basic frame as manufactured is marginal, strengthwise for the purpose that the vehicle was designed for.

When you start adding upwards of 12" extra track and wheelbase, longer suspension travel, heavier rate springs etc. along with all of the other bolt on modifications available, then you had better start looking at bracing the chassis to support these added loads.

the F1 ENGINEERING race engineered front, rear and intermediate rear suspension Shear Plates have been designed to directionally feed the loads across the chassis, acting as load dissipating bulkheads.

Suspension Shear Plate for the Rhino 450/660 and 700, come complete with all metric grade 12.9 hardware.

F1 ENGINEERING has spent many hours designing a new rack housing system that is pretty much bullet proof, yet is a simple bolt in upgrade.

Our rack housing is CNC machined from a single billet of 6061-T6 aircraft quality aluminum, high strength aluminum bronze bushings are pressed into each end to support the rack gear,where the factory unit just floats around.

The rack gear itself is machined from a round bar of 300M alloy steel, a full 7/8" diameter on the standard 9 tooth assembly and 1.0" diameter on the 10 tooth race rack. The gear is then heat treated to 200,000 psi tensile strength and then carbon nitride plasma coated to increase tooth strength and to give corrosion resistance.

Some of our competitors use a square section rack gear as they are readily available commercially, this also makes the housing easier to machine by just milling a slot into the two or three housing half sections, this of course opens the possibility of movement or failure at the joints.

We prefer to go the more difficult route and use the stronger round section rack gear and align boring the single piece housing to maintain the structural integrity of the whole unit, this also keeps the close tolerances that we require for minimum backlash in the gears.

The helical pinion gear is CNC hobbed from H11 aerospace tool steel and through hardened.